2011 Mercruiser 350 Magnum Full Or OK
Mercury OptiMax Outboard Boat Motor service manuals are available for.Mercruiser 350 mag mpi owners manual Seloc takes repair into the 21st century, by allowing users to access our electronic database for up-to-the minute information on your engine. IMPORTANT: Failure to follow these timing procedure instructions will result in improper timing causing performance problems and possible severe damage to marine engines.67 Mercury Marine/Mercruiser New OEM Compressor Kit, 8M0133589 Air Compressor. If you desire to droll books, lots of novels, tale, jokes, and more fictions collections are next launched, from best. Engine Model Engine Oil Capacity Fluid type 350 MAG and SeaCore 350 MAG 4.25 L (4.5 US qt) Mercury MerCruiser FullSynthetic Engine Oil, 20W40 377 MAG and SeaCore 377 MAG 90-8M0050539.Shop the PPT Online Store to Buy Mercruiser Engines & Longblocks……Read MoreMercruiser 350 Alpha Mag Service The MerCruiser 350 5.7L Mag MPI service manual provides detailed step-by-step instructions to boat owners accompanied by.Acces PDF Mercruiser 454 Magnum Mpi Manual Mercruiser 454 Magnum Mpi Manual If you ally dependence such a referred mercruiser 454 magnum mpi manual books that will manage to pay for you worth, acquire the no question best seller from us currently from several preferred authors. Add the specified engine oil to bring the level up to, but not over, the full or OK range mark on the dipstick.
Chalk or white paint on timing mark on damper may help visibility.3. Install a jumper wire between the two WHITE leads on the distributor. Refer to Specifications – “Engine Rotation and Firing Order,” for cylinder numbering and location.NOTE: Before starting engine make sure the timing tab and mark on damper are clean. Connect power supply leads on light to 12 volt battery. As well as propelling crafts outboard motors also.1. Connect timing light (91-99379 or similar) to No. The systems are self-contained units consisting of the engine, propeller and the gearbox. MerCruiser motors are propulsion systems used in boats.
Tighten clamp and recheck location of timing mark.7. Make sure that the distributor has been tightened. Allow engine to reach normal operating temperature.5. Aim timing light at timing tab, located on the timing gear cover and crankshaft torsional damper.6. If adjustment is required, adjust timing by loosening distributor clamp and rotating distributor body as required until timing mark on damper or pulley lines up with the mark on tab specified in “Specifications”. Chalk or white paint on timing marks may help visibility.4. Start engine and run at normal idle speed.
Connect power supply leads, if applicable, on light to 12 volt battery. This means that the additional timing advance features would not function.Two items of test equipment are required: an inductive pickup timing light and one of either a Scan Tool, Marine Diagnostic Code Tool or MerCruiser Special Timing Tool (Quicksilver 91-805747A1).1. Connect timing light (91-99379 or similar) to No. If the jumper wire is left in place, the ignition module will operate in the “Base Timing Mode”.
Slowly rotate the distributor clockwise or counterclockwise to adjust the timing to specified degrees.9. Aim timing light at timing tab and recheck location of timing mark. Refer to “Specifications.”7. Loosen the distributor clamp bolt enough to just be able to rotate the distributor with some resistance.8. Aim timing light at timing tab and recheck location of timing mark. Allow it to reach normal operating temperature.5. On all models except 350 Mag MPI: Manually adjust the engine throttle to 1800 RPM.6. Aim timing light at timing tab, located on the timing gear cover and crankshaft torsional damper. You do not have to increase it manually, as stated in the following steps.3. Connect the Timing Tool (or appropriate tool, as listed above) to the DLC connector (in the electrical box or on the electrical bracket) of the wiring harness.4. Start the engine. On 350 Mag MPI Model, engine RPM will automatically increase to a higher RPM. Chalk or white paint on timing marks may help visibility.NOTE: If NOT Using MerCruiser Timing Tool: With engine running, set the scan tool or Marine Diagnostic Code Tool to the SERVICE MODE and follow manufacturer’s instructions.
Turn ignition key to OFF position.
0 kommentar(er)
